Please note: we're the original and only source of our independently validated Green Machines. This is a very specific and exact technology.
Therefore, we cannot guarantee or troubleshoot issues with reportedly similar products sold around the web. Thank you for your understanding.

Brown's Gas Injector

Saves 15-25+ MPG
For only $195.00!


There are three units in this system. The Injector (installed under the hood), the Electrolyzer for charging the water, and the water container. Read on to learn more about each one:


A) Brown's Gas Injector


This injector is identical to the "Water Gas Injector" except that the water in the container is different. It has been "charged" with Brown's Gas and fortified by adding 2tsp. of Hydrogen Peroxide. This supercharged mixture is drawn out of the top of the bottle by the engine vacuum and transported to the manifold where, in a catalytic reaction, it bonds with the carbon chains in gasoline. The unique bond between gasoline carbon chains and Brown's gas increases the power output of the fuel by a factor of 3.8. This means you get better gas mileage, improved performance, and near complete combustion of exhaust pollutants.




B) Brown's Gas Charging Electrolyzer (charges water)


The pump uses air pressure to move the Brown's Gas from the top of the electrolyzer jar into the container below where the water is being charged. The Brown's Gas mixes with the container water as it rises to the surface in the form of bubbles.

It takes about thirty minutes to charge a quart of water. When the charging is complete, two teaspoons full of hydrogen peroxide are added to the water and the water is transferred to the injector unit located under the hood of the car. An alternative water transfer method is to remove the jar from the vehicle - it's easy to disconnect - and bring it inside where it can be washed and refilled. The water in the injector unit should be changed about once a week, more often if you drive long distances.




C) Charging Container


The charged water in this container is transferred to the water vapor injector located under the hood of the vehicle. Charging the water takes 30 minutes and the charge lasts about a week.

The Brown's Gas Injector runs under the radar of most OBD1 and OBD2 car technology. If not, a scan gage and air pressure adjuster may be required.




Fig. 1) Overview of the three units and their accessory parts:

Brown's Gas Injector Parts List
  • (1) WaterToGas Brown's Gas Charging Electrolyzer
  • (1) WaterToGas Brown's Gas Vapor Injector
  • (1) Air pump
  • (1) 3 volt 400 ma Charger
  • (1) Air volume control
  • (1) 6" x 1/8" vacuum hose
  • (1) Air Bubbler
  • (1) 1/6" x 1/4" bubbler supply hose
  • (2) 1/8" elbow connector
  • (4) 1/2" x 1/4" ss fender washers
  • (1) 1' of 1/8" (inside diam) vacuum hose
  • (1) 1/8" x 6" flexible attachment cord
  • (1) 4 foot vacuum hose
  • (1) Universal vacuum tee
  • (1) Installation Instructions
  • Electrolyzer Parts:
  • (4) 2" x 1/4" ss (stainless steel) fender washers
  • (2) 1/4" x 6 1/2" ss rod (anode/cathode)
  • (4) 1/2" x 1/4" ss fender washers
  • (2) 1/4" ss wing nuts
  • (2) 1/8" elbow connector
  • (18) 1/4" ss nuts
  • (4) 1/4" ss lock washers



All parts and components have been thoroughly tested, optimized and validated for performance and efficiency. Backed by our 100% satisfaction guarantee, our kits are extremely durable and easily install on over 99.9% of motor vehicles.






Lang Brothers Video
Tom and Bill discuss the benefits of the Green Machines and how and why they work.
WaterToGas.com Radio Interview

Bill Lang interviewed by the Kentucky Water Fuel Museum

Soon after the interview, we validated those high output results and launched our most powerful and popular systems to-date, the Brown's Gas Injector and our 2nd-generation HydroCharger product line.